Optimize cutting tool performance, spindle RPM, and table feed rates across aluminum, tool steel, stainless, and exotic alloys. Calibrated with OEM machine tool limits from CNCBUY's verified database.
| Standard | Thread Designation | Nominal Diam. | Pitch / TPI | Tap Drill Size | Decimal (in / mm) | Close Clearance |
|---|---|---|---|---|---|---|
| Metric | M3 x 0.5 (Coarse) | 3.0 mm | 0.50 mm | 2.50 mm (#39) | 0.0980" / 2.50 mm | 3.40 mm |
| Metric | M4 x 0.7 (Coarse) | 4.0 mm | 0.70 mm | 3.30 mm (#30) | 0.1285" / 3.30 mm | 4.50 mm |
| Metric | M5 x 0.8 (Coarse) | 5.0 mm | 0.80 mm | 4.20 mm (#19) | 0.1660" / 4.20 mm | 5.50 mm |
| Metric | M6 x 1.0 (Coarse) | 6.0 mm | 1.00 mm | 5.00 mm (#9) | 0.1969" / 5.00 mm | 6.60 mm |
| Metric | M8 x 1.25 (Coarse) | 8.0 mm | 1.25 mm | 6.80 mm (Letter H) | 0.2660" / 6.80 mm | 9.00 mm |
| Metric Fine | M8 x 1.0 (Fine) | 8.0 mm | 1.00 mm | 7.00 mm (Letter J) | 0.2756" / 7.00 mm | 9.00 mm |
| Metric | M10 x 1.5 (Coarse) | 10.0 mm | 1.50 mm | 8.50 mm (Letter R) | 0.3346" / 8.50 mm | 11.00 mm |
| Metric | M12 x 1.75 (Coarse) | 12.0 mm | 1.75 mm | 10.20 mm (13/32") | 0.4016" / 10.20 mm | 13.50 mm |
| Metric | M16 x 2.0 (Coarse) | 16.0 mm | 2.00 mm | 14.00 mm (35/64") | 0.5512" / 14.00 mm | 17.50 mm |
| UNC Coarse | 1/4" - 20 UNC | 0.250" | 20 TPI | #7 Drill (0.2010") | 0.2010" / 5.10 mm | 0.2660" (Letter H) |
| UNF Fine | 1/4" - 28 UNF | 0.250" | 28 TPI | #3 Drill (0.2130") | 0.2130" / 5.41 mm | 0.2660" (Letter H) |
| UNC Coarse | 3/8" - 16 UNC | 0.375" | 16 TPI | 5/16" Drill | 0.3125" / 7.94 mm | 0.3970" (Letter X) |
| UNC Coarse | 1/2" - 13 UNC | 0.500" | 13 TPI | 27/64" Drill | 0.4219" / 10.72 mm | 0.5312" (17/32") |
| UNC Coarse | 5/8" - 11 UNC | 0.625" | 11 TPI | 17/32" Drill | 0.5312" / 13.49 mm | 0.6562" (21/32") |
| UNC Coarse | 3/4" - 10 UNC | 0.750" | 10 TPI | 21/32" Drill | 0.6562" / 16.67 mm | 0.7812" (25/32") |
| NPT Pipe | 1/8" - 27 NPT | 0.405" | 27 TPI | Letter R (or 21/64") | 0.3390" / 8.61 mm | N/A (Tapered) |
| NPT Pipe | 1/4" - 18 NPT | 0.540" | 18 TPI | 7/16" Drill | 0.4375" / 11.11 mm | N/A (Tapered) |
| NPT Pipe | 1/2" - 14 NPT | 0.840" | 14 TPI | 23/32" Drill | 0.7188" / 18.26 mm | N/A (Tapered) |
Spindle RPM is inversely proportional to tool diameter. Smaller end mills (e.g. 1/8" or 3 mm) require significantly higher RPM to achieve the required Surface Feet per Minute (SFM), whereas large face mills run at lower RPM to avoid overheating the cutting edge.
A 75% thread engagement provides nearly 100% of full thread shear strength while dramatically reducing tapping torque and the risk of breaking taps in expensive workpieces, especially in tough alloys like stainless and titanium.
When taking light radial stepovers (less than 50% of cutter diameter), the actual chip created is thinner than the programmed advance per tooth. To maintain optimal chip thickness and prevent rubbing, the feed rate must be increased.